Equipment Guide23 min readUpdated 2026-11-17

Vertical Vacuum Furnace: Load Path, Seal and Uniformity

Why a vertical vacuum furnace behaves differently: seal plane, load path, axial uniformity from 800 to 1,300 mm, tonnage-vs-pressure maths, and what to put in the RFQ.

A vertical vacuum furnace is a batch furnace whose chamber axis is vertical, so the workload enters from above or below instead of through a side door. That single change moves the vacuum seal into a horizontal plane, makes the bottom plate carry the load, and turns the height of the hot zone into the dominant temperature-uniformity variable.

What a vertical vacuum furnace actually changes

The short answer: orientation is not a packaging choice, it is a specification. In a horizontal furnace the door, the hearth and the thermal insulation are three separate parts doing three separate jobs. In a vertical furnace they collapse into one interface — the plate the load stands on is also the vacuum boundary and also the main heat leak. Every number that matters downstream (achievable uniformity, seal life, lift height, installation footprint) follows from how a supplier solves that one interference. This page sets out what the published record supports, what it does not, and which questions separate a workable vertical furnace from a well-dressed brochure. All catalogue values below are cited by printed page; derived figures are labelled and reproducible.

Key facts

  • ✓A vertical chamber's usable volume scales as D²H, while its heated wall area scales roughly as DH — so power per litre falls steeply with size, while power per m² of hot-zone wall falls only ~2× across a 63× volume range (derived below).
  • ✓Across every vertically oriented platform in the HuanYu catalogue that publishes dimensions, height-to-diameter ratio sits between 1.00 and 1.88; none exceeds 2.
  • ✓Published uniformity is ≤±3 °C at 500 mm of vertical height and ±1 °C at 800 mm, but the same catalogue quotes ±5 °C at 1,300 mm — height, not controller quality, sets the tolerance.
  • ✓A horizontal seal plane is not longer than a vertical one: at ~0.2 m² of chamber cross-section, a Ø500 mm circle and a 600 × 400 mm rectangle differ by 4% in seal length per unit area (8.0 vs 8.33 m/m²).
  • ✓Press tonnage without part footprint is not a pressure. At a 40 MPa graphite-tooling limit, the catalogue's 5–200 T ladder maps onto part diameters of Ø39.5 mm to Ø250 mm — and Ø250 mm is exactly the largest published chamber (derived).
  • ✓Pressure-rise thresholds must be multiplied by chamber volume before comparison: the vertical carbon-tube furnace's ≤2 Pa/h on 48.3 L equals 0.0965 Pa·m³/h, about 1.5× the absolute leak allowed by the 0.67 Pa/h quoted for a 96 L horizontal chamber (derived).
  • ✓HuanYu Technology Equipment: 60 product series, 500+ models, 10+ years, GB/T 19001-2016 / ISO 9001:2015 (certificate U25Q2SH8002817R3M).

Which architectures are called "vertical"?

Four distinct machines share the word, and they are not interchangeable. Buyers who compare them on temperature alone usually buy the wrong one.

ArchitectureLoad directionSeal planeTypical published rangeWhere the design pressure goes
Bottom-load lift (elevator)

Load rises into a fixed chamber

Horizontal, at floor level

1750 °C / 1650 °C working (catalogue pp.27–28); site lift family 1400 / 1700 °C

Seal must survive radiant heat from below and debris from the load

Top-load / bell

Chamber descends over the load

Horizontal, at the top of the base

SiC-heated bell, shell <45 °C at max temperature (catalogue pp.17–24)

Lifting gear and the seal's concentricity

Pit furnace

Load lowers into a fixed pit

Horizontal, at floor level, inverted

1200 °C and 1700 °C published (site); 1200 °C / 1100 °C working, five-side heating (catalogue pp.17–24)

Pit drainage, cable routing, floor loading

Fixed vertical chamber / tube

Load inserted from top or bottom

Two horizontal flanges

Up to 1700 °C (site vertical tube); 1100 °C infrared tube (catalogue pp.1–7)

Both flange seals, plus tube support

Two of these are frequently confused. A pit furnace is a vertical furnace you stand over; a bottom-load lift furnace is a vertical furnace the load rises into. Both publish horizontal seals at floor level, but the pit furnace is limited by how deep you are willing to dig and the lift furnace by how high your building is.

Why the bottom plate is the whole design

In a bottom-load vertical furnace one plate performs three jobs at once, and each job pushes the plate in a different direction.

It is the vacuum boundary. A horizontal seal of 0.5–1.6 m circumference has to hold 10⁻³ Pa against atmospheric pressure over a diameter that grows with chamber size. Seal length grows linearly with diameter (0.503 m at Ø160, 1.571 m at Ø500), but the load it must resist grows with area.

It is the hearth. The load stands on it, at temperature. The catalogue publishes no load rating for any vertical platform, so a vertical furnace's allowable load is per project written confirmation — not a number you can read off a page. Anyone quoting kilograms without a drawing is guessing.

It is a thermal short. The plate is the one path that connects a 1650 °C hot zone to a water-cooled flange a few hundred millimetres away. Suppliers answer this with a thermal break, a cooled collar, or distance. Whichever they choose, the top of the plate runs colder than the hot zone, and the bottom of the load runs colder than the top.

That third consequence is measurable and it is the reason vertical furnaces behave differently from horizontal ones: the coldest point of the load is where the load touches the plate. In a horizontal furnace the coldest point is usually the door end, which you can shield with a baffle. In a vertical furnace you cannot shield the floor without also blocking the load path.

Does a round chamber really seal better?

Not for the reason usually given. Run the perimeter arithmetic and the "round chambers seal better" claim collapses into something narrower and more useful.

ChamberCross-sectionPerimeterPerimeter per m²
Ø160 mm

0.0201 m²

0.503 m

25.0 /m

Ø200 mm

0.0314 m²

0.628 m

20.0 /m

Ø250 mm

0.0491 m²

0.785 m

16.0 /m

Ø320 mm

0.0804 m²

1.005 m

12.5 /m

Ø500 mm

0.1963 m²

1.571 m

8.0 /m

400 × 300 mm

0.1200 m²

1.400 m

11.7 /m

600 × 400 mm

0.2400 m²

2.000 m

8.3 /m

900 × 600 mm

0.5400 m²

3.000 m

5.6 /m

(Perimeters and areas computed from published dimensions; ratio is derived.)

At roughly 0.2 m² of cross-section — the size of a Ø500 mm lift chamber or a 600 × 400 mm brazing chamber — the circle gives 8.0 m of seal per m² and the rectangle 8.33. Four percent. The isoperimetric advantage of a circle is real but it is almost irrelevant at the scale buyers actually purchase.

What does matter is the plane of the seal:

  • ✓A vertical door seal (the 400 × 300 / 600 × 400 / 900 × 600 mm molybdenum-lanthanum brazing platform, catalogue p.35, uses an electrically driven door lock) is wiped by gravity on every cycle, and debris falls away from the groove.
  • ✓A horizontal seal at the bottom of a vertical furnace collects whatever falls: oxide flakes from the hot zone, condensate from the load, dust from loading. It is the single most common reason a vertical furnace that passed a factory acceptance test drifts upward on pressure rise after twenty cycles.

So the buying question is not "round or square" but "is the horizontal seal shielded, and can I inspect it without dismantling the lift?"

Axial uniformity: where the height goes

The most useful number in the whole vertical category is buried in a debinding furnace specification: uniformity of ±1 °C at 800 mm and ±5 °C at 1,300 mm (catalogue pp.17–24). That is one platform, one controller, one element family — and a 1.63× increase in height turns ±1 °C into ±5 °C. Five times the error for 63% more height.

The rest of the catalogue agrees with the direction, if not the magnitude:

PlatformVertical height publishedPublished uniformitySource
Lift furnace (HTCC)

300 mm (Ø200)

≤±3 °C

catalogue pp.27–28

Lift furnace (HTCC)

500 mm (Ø500)

≤±3 °C

catalogue pp.27–28

Debinding furnace

800 mm

±1 °C

catalogue pp.17–24

Debinding furnace

1,300 mm

±5 °C

catalogue pp.17–24

Molybdenum-tungsten wire furnace

120–250 mm

±1 °C

catalogue p.32

Lift furnace (SJL family)

96–1,200 L, dimension to confirm

±1 °C control / ±3 °C uniformity

catalogue pp.3–8

Pit furnace

600 mm

±0.5 °C control

catalogue pp.17–24

Read as a set, the pattern is: ±1 °C is achievable up to about 800 mm of vertical height, ±3 °C to about 500 mm in a production platform, and beyond ~1,000 mm you should expect ±5 °C unless the hot zone is divided into independently controlled zones. Note that ±0.5 °C and ±1 °C in that table are control accuracies (thermocouple-and-controller performance), while ±3 °C and ±5 °C are furnace uniformity values across a volume. They are not the same measurement and cannot be compared to each other — a point the manufacturer-audit guide treats as the first line of a specification review.

There is a second, structural reason vertical furnaces lose uniformity at the top. In a horizontal tube furnace the two ends are symmetric: insulation at both ends, radiation losses balanced. In a top-load or bottom-load vertical furnace one of the six faces is a lid, and the lid is colder than the walls because it is thin, close to the flange, and often the only face not actively heated. The pit furnace specification makes this explicit by heating from five sides only (catalogue pp.17–24) — the sixth face is the opening. Five-sided heating is not an economy measure; it is an admission that the sixth face cannot be heated.

The practical consequence: ask for a nine-point survey at temperature, in the as-loaded condition, and ask where the coldest point was. If the answer is "the top", you need a top zone, not a better controller. If the answer is "the bottom, under the load", no controller will fix it.

Height is a building constraint before it is a furnace constraint

A bottom-load lift furnace needs the chamber height plus the full lift travel plus clearance for the load and the loading device. In practice the machine's installed height is roughly twice its chamber height, and that number — not the chamber — decides whether the furnace fits.

Three consequences that appear in every vertical project:

  1. 01

    The crane or hoist becomes part of the specification. A top-load bell needs lifting gear rated for the chamber plus insulation; a bottom-load lift needs a loading height that a forklift or scissor table can reach.

  2. 02

    Pit furnaces trade height for excavation. The pit version of the same 600 mm cube (catalogue pp.17–24) needs a drained, load-rated pit with a cable route that survives the lid. Sites that cannot dig buy the lift.

  3. 03

    Service access is vertical. Replacing a heating element in a horizontal furnace is a side operation; in a vertical furnace it is usually a top operation, which means the crane again.

Published vertical platforms, side by side

Everything below is a published value. Where the source is the website it is marked "site"; where it is the printed catalogue the printed page is given. Blank cells mean the value is not published, not that it is unimportant.

PlatformOrientation statedMax temperatureWorking temperatureChamberPowerVacuum / pressureUniformitySource
Carbon-tube furnace ZKT

Vertical, double water jacket

2,000 °C (ZKT-210-23: 2,300 °C)

—

Ø90 × 120 → Ø320 × 600 mm

25 / 40 / 50 / 85 / 100 / 120 / 210 kW

6.67 × 10⁻³ Pa; ≤2 Pa/h

—

catalogue pp.19–20

Lift furnace (HTCC)

Vertical lift

1,750 °C

1,650 °C

Ø200 × 300 / Ø500 × 500 mm

28 / 120 kW

<50 Pa; ≤40 kPa gauge

≤±3 °C

catalogue pp.27–28

Vacuum hot press

Vertical ram (up / down / both)

1,000–2,300 °C

—

Ø160 × 160 / Ø250 × 250 mm

80 / 130 kW

10 Pa / 5 × 10⁻³ / 5 × 10⁻⁴ Pa selectable; ≤5 Pa; 0.67 Pa/h

—

catalogue p.34

Molybdenum-tungsten wire furnace

Not stated

2,000–2,300 °C

—

Ø80 × 120 / Ø160 × 160 / Ø200 × 250 mm

24 / 45 / 65 kW

Not published

±1 °C

catalogue p.32

Vacuum melting furnace ZKR

Not stated

2,200 °C

—

Crucible 1–1,500 kg (steel)

15–800 kW, 1,000–4,000 Hz

6.67 × 10⁻³ Pa; ≤2 Pa/h

±5 °C

catalogue p.20

Lift furnace SJL family

Vertical, servo screw lift

1,200 / 1,400 / 1,700 °C by element

—

96–1,200 L (dimension to confirm)

18–150 kW

Not published

±1 °C control / ±3 °C uniformity

catalogue pp.3–8

Pit furnace

Vertical (pit)

1,200 °C

1,100 °C

600 × 600 × 600 mm

30 kW

Air / controlled atmosphere

±0.5 °C control

catalogue pp.17–24

Bell furnace

Vertical (top-load)

SiC element; shell <45 °C at max

—

Not published

Not published

Not published

Not published

catalogue pp.17–24

Vertical infrared tube furnace

Vertical tube

1,100 °C

1,000 °C

Tube, dimension not published

1–20 °C/min ramp

6.67 × 10⁻² / 10⁻³ Pa

—

catalogue pp.1–7

Vertical tube furnace

Vertical tube, two flange seals

Up to 1,700 °C

—

Quartz / corundum / stainless tube

Not published

Vacuum / controlled atmosphere

Not published

site

Vertical atmosphere furnace

Vertical

Up to 1,000 °C

—

Not published

Not published

Controlled atmosphere

±5 °C control

site

Pit furnace

Vertical (pit)

1,200 °C / 1,700 °C

—

Configuration specific

Not published

Air / controlled atmosphere

—

site

Lift furnace

Vertical lift

1,400 °C / 1,700 °C (VSF1700-I, SJF1700-I)

—

Configuration specific

Not published

Air / controlled atmosphere

—

site

The shape of that table is itself a finding: the catalogue documents vertical platforms with numbers; the website documents them with categories. Of the four website entries, three publish no chamber dimension at all.

Derived checks you can run in thirty seconds

The published record rarely pairs the values a buyer needs. These four derived checks close the gaps without inventing anything.

1. Power per litre falls fast; power per m² barely moves

The carbon-tube family covers Ø90 × 120 mm to Ø320 × 600 mm (catalogue pp.19–20). Those are 0.763 L and 48.25 L — a 63× volume range — while the published power list runs 25 kW to 210 kW, an 8.4× range.

ReadingSmall end (Ø90 × 120)Large end (Ø320 × 600)Ratio
Volume

0.763 L

48.25 L

63.2×

Power (endpoint pairing)

25 kW

210 kW

8.4×

Power per litre

32.7 kW/L

4.35 kW/L

7.5×

Heated wall area

0.0467 m²

0.764 m²

16.4×

Power per m² of wall

536 kW/m²

275 kW/m²

1.95×

Endpoint pairing assumes the catalogue's power list runs smallest-to-largest in the same order as its size list; the catalogue does not state the pairing, so treat 32.7 and 4.35 kW/L as derived under that assumption. The conclusion survives the assumption either way: comparing kW per litre between two vertical furnaces of different size is meaningless, and 275–536 kW/m² at 2,000–2,300 °C is consistent with the T⁴ scaling that makes a 1,300 °C hot zone need only ~50 kW/m².

The lift family gives the same lesson at lower temperature: 96 L at 18 kW and 1,200 L at 150 kW is 0.188 → 0.125 kW/L, only 1.5× apart across a 12.5× volume range (derived, catalogue pp.3–8).

2. Tonnage is not pressure

The vacuum hot press publishes 5–200 T on Ø160 and Ø250 chambers (catalogue p.34). Referred to the chamber cross-section — the largest part that can physically be pressed — that spans 1.0 MPa to 97.5 MPa, a 16.4× spread from a 40× tonnage range, because area also changed 2.44×.

The useful direction is the inverse. Graphite tooling is generally limited to a few tens of MPa (general engineering range), so tonnage sets your maximum part area, not your maximum pressure:

TonnageMax part area at 40 MPa (derived)Equivalent diameter
5 T

0.00123 m²

Ø39.5 mm

50 T

0.0123 m²

Ø125 mm

200 T

0.0490 m²

Ø250 mm

The last line is the elegant part: at a 40 MPa tooling limit, 200 T covers exactly a Ø250 mm part — which is exactly the largest chamber the same catalogue page publishes. The tonnage ladder and the chamber ladder were evidently designed against the same tooling assumption, which is a good sign for the platform and a useful cross-check on any competitor's quote.

3. Pressure rise must be multiplied by volume

The vertical carbon-tube furnace quotes ≤2 Pa/h; the horizontal brazing platform quotes ≤0.67 Pa/h (catalogue p.35). The vertical furnace looks three times leakier. It is not, once volume is included:

ChamberVolumeQuoted riseAbsolute leak rate (derived)
Ø90 × 120 mm

0.763 L

2 Pa/h

0.0015 Pa·m³/h

Ø320 × 600 mm

48.25 L

2 Pa/h

0.0965 Pa·m³/h

600 × 400 × 400 mm (horizontal)

96 L

0.67 Pa/h

0.0643 Pa·m³/h

The largest vertical chamber is allowed 1.5× the absolute leak of the mid-size horizontal one, and the smallest is allowed 1/43 of it. A single Pa/h number, quoted without volume, tells you nothing about build quality — it tells you which chamber the number was written for.

4. Height-to-diameter converges

Compute H/D for every vertical platform that publishes both dimensions: 120/90 = 1.33; 600/320 = 1.88; 300/200 = 1.50; 500/500 = 1.00; 160/160 = 1.00; 250/250 = 1.00; 200/190 = 1.05; 600/600 = 1.00. Range 1.00–1.88, none above 2.

That is not a coincidence; it is the point at which axial gradient becomes commercially unsellable. If a supplier offers a vertical chamber with H/D above ~2, the first question is the measured top-to-bottom spread at temperature, not the controller.

Publication inconsistency on our own pages

Three defects in HuanYu's own published record are relevant to anyone researching this category, and we would rather document them than have a buyer find them first.

1. The vertical atmosphere furnace page carries laboratory muffle-furnace text. /products/vertical-atmosphere-furnace-19/ publishes Up to 1,000 °C and ±5 °C control accuracy, but its technical description is copied from a coal-ash determination muffle: it describes "the ash or volatile content of a batch of coal samples", a 0–5,999 minute timer, and a unit that can "replace the old muffle furnace". Meanwhile the same site publishes 1,200 / 1,700 °C for its pit furnace and 1,400 / 1,700 °C for its lift furnace. A 700 °C disagreement inside one vertical family is a page-level error, not a product limit.

2. The lift furnace page publishes four models and no chamber. /products/lift-furnace/ lists 1,700 °C, 1,700 °C, 1,400 °C and 1,700 °C across four rows (two of them reading "Model to be confirmed", two named VSF1700-I and SJF1700-I), with capacity "Configuration specific" on every row. A lift furnace without lift height and travel cannot be installed, so this page cannot currently close a sale on its own.

3. One vertical product page is orphaned and quotes a different phone number. /products/vertical-furnace (VTL1600-I, vacuum melting) publishes melting capacity and maximum temperature both as "Configuration specific" — so the "1600" in the model name is not a published temperature — appears in no sitemap, and lists +86 17189516981 where current pages list +86 17184862478. The model may be perfectly good; the record is inconsistent, and inconsistency is what a technical buyer tests for.

Our position is consistent with every previous guide in this library: the printed catalogue is the technical record, the website is the configuration record, and the quotation governs. Where the two disagree we say so, and we fix the page.

Troubleshooting a vertical furnace

Vertical-specific failure modes cluster around three interfaces. This table assumes the general pressure–heat–control isolation sequence in the vacuum furnace troubleshooting guide has already been run; it only adds what changes when the axis is vertical.

SymptomMost likely causeCheckAction
Top third of load under-processed

Lid heat loss, single-zone hot zone

Nine-point survey in the as-loaded condition

Add a top zone or trim element taps; do not re-tune the controller

Bottom of load cold, top correct

Thermal short through the load plate

Contact and IR check of the plate and bottom flange

Thermal break or cooled collar; re-survey

Pressure rise climbs after 10–30 cycles

Debris or condensate in the horizontal seal groove

Isolate with a blank flange, then leak-test the plate alone

Shield the seal plane, add a sacrificial groove cover, revise loading practice

Particulate on upward-facing surfaces

Pump port above the load, or convection carrying debris

Inspect port position and any baffle

Move the port or add a baffle; clean the hot-zone ceiling

Load tilts or settles during the cycle

Hearth creep or uneven support at temperature

Hearth flatness cold, then loaded hot

Replace the hearth plate; specify a supported, not cantilevered, hearth

Lift judders or slows

Screw, nut or guide wear; load above rating

Servo torque log against commissioning baseline

Service the lift; obtain a written load rating

Reaches vacuum cold but not hot

Outgassing from insulation that absorbed moisture

Rise test cold, then hot, then after bake-out

Bake-out cycle; check insulation for handling damage

Uniformity drifts over months

Thermocouple drift or element ageing

Cross-check with an independent survey thermocouple

Replace the control TC; log element resistance

What to put in the RFQ

Eleven fields separate a quotable vertical furnace from a brochure:

  1. 01

    Part or load envelope, including the face that rests on the plate.

  2. 02

    Load mass and how it is supported — this is the number the supplier must warrant.

  3. 03

    Required uniformity, stated as a volume and a tolerance, not a controller accuracy.

  4. 04

    The height over which that uniformity must hold.

  5. 05

    Maximum and continuous temperature, named separately.

  6. 06

    Atmosphere or vacuum level, plus whether positive pressure is needed.

  7. 07

    Pressure-rise acceptance value and the chamber volume it applies to.

  8. 08

    Lift travel and the installed height available in your building.

  9. 09

    Loading method — crane, hoist, forklift, scissor table — and its reach.

  10. 10

    Cycle profile including cooling rate and how the load is cooled.

  11. 11

    Acceptance test: nine-point survey, rise test, and who witnesses them.

Frequently asked questions

What is a vertical vacuum furnace?

A batch furnace whose chamber axis is vertical, with the load entering from above (top-load, bell) or below (bottom-load lift, pit). The vacuum seal sits in a horizontal plane and the load-bearing plate is also part of the vacuum boundary.

Bottom-load or top-load — which should I buy?

Bottom-load when the load is heavy or must be positioned precisely on a hearth, because the load never hangs. Top-load when the chamber must be lifted clear for access or when the load is light and the building has crane height but no floor space. Pit furnaces suit long parts that would otherwise need a very tall building.

Why do vertical furnaces have a height limit?

Because axial gradient grows with height faster than control quality improves. One published HuanYu platform quotes ±1 °C at 800 mm and ±5 °C at 1,300 mm; every vertical platform in the catalogue with published dimensions sits at H/D between 1.0 and 1.88.

Can a vertical furnace hold ±3 °C over its full height?

Yes, up to roughly 500 mm of vertical height in the published record (HTCC lift, Ø200 × 300 and Ø500 × 500, catalogue pp.27–28). Beyond about 1,000 mm you should specify independent zone control and verify with a survey.

Is a round chamber better for vacuum than a rectangular one?

For seal length, almost not: at ~0.2 m² cross-section a Ø500 mm circle and a 600 × 400 mm rectangle differ by 4% in perimeter per unit area. Round chambers are easier to machine and to shield; rectangular chambers use floor area better. What actually determines leak behaviour is whether the seal plane is shielded.

How do I compare tonnage between two vertical hot presses?

Convert tonnage to pressure over the part footprint. 200 T over a Ø250 mm part is ~40 MPa; the same 200 T over a Ø40 mm part is over 1.5 GPa, which no graphite die survives. Ask for the ram diameter and the tooling limit, not just the tonnage.

How much height do I need above the furnace?

Roughly the chamber height plus full lift travel plus loading clearance — in practice about twice the chamber height for a bottom-load lift. Confirm against the supplier's general arrangement drawing before signing a lease.

Can a pit furnace go below floor level on an upper floor?

Rarely. Pit furnaces need drainage, a load-rated pit structure and cable routing that survives the lid. If excavation is not possible, the lift furnace is the substitute, and the space cost moves from floor to height.

What pressure rise should I ask for on a vertical furnace?

Ask for the value in Pa/h and in Pa·m³/h. A 48 L vertical chamber at 2 Pa/h allows 0.0965 Pa·m³/h, about 1.5× the absolute leak of a 96 L chamber quoted at 0.67 Pa/h. Without the volume, the number cannot be compared.

When is a horizontal furnace the better choice?

When the part is a large flat plate, when the load must be supported along its length, when uniformity matters more than floor area, or when the building has no vertical clearance. The vertical advantage is floor area and gravity-assisted loading; the cost is height, a horizontal seal, and an axial gradient.

Does orientation change the vacuum level I can reach?

Not fundamentally — the pump set does. The catalogue's vertical carbon-tube furnace reaches 6.67 × 10⁻³ Pa with an oil diffusion pump backed by a rotary vane pump and PLC high/low-vacuum switching (pp.19–20), the same order as horizontal platforms using the same pump architecture. What changes is where leaks and debris accumulate.

Need help applying this?

Bring the guide into a real equipment conversation.

Discuss your process